Description of changes contained in version 2.03 (1/7/2010)
	Fix: MIB not compiling properly in NET-SNMP
	Fix: SNMP didn't always report long friendly names

Description of changes contained in version 2.02 (12/14/2009)
	Change: Improved interoperability with poorly-behaved SNMP agents
	Fix: Current readings above 80A were not displayed properly via SNMP

Description of changes contained in version 2.01 (7/2/2009)
	Note: EM 2.xx is a major rewrite of the EM meter platform that addresses several issues present in the EM 1.xx platform.
	Note: EM 1.xx to 2.xx upgrades require the use of Geist ASU.
	Add: SNMP sysName, sysContact and sysLocation are now settable via the “Display” page on the web interface.
	Fix: SNMP speed has been greatly increased.  Retrieving all of the available information on the meter takes less than 2 seconds in most cases.
	Fix: EM meters no longer stop responding when attached to 10/100/1000Mbps network equipment.
	Fix: Various other performance enhancements and interface improvements.
	Change: Improved interface consistency across firmwares.
	Change: All EM meters now share the same MIB, allowing for easier integration with management software.

Description of changes contained in version 1.60 (4/1/2009)
	Add: New firmwares -- EM40/GM33, EM40/GM31, EM8/GM7-15, EM8/GM5, EM8/GM3P-80
	Add: Support for upcoming Console 3.0 release
	Fix: Mislabeled Circuit 1 and Circuit 2 in GM2 firmware
	Fix: Slightly faster web page generation

Description of changes contained in version 1.55 (11/21/2008)
	Fix: Bug introduced in 1.50 causing alarm and warning levels to not always save correctly
	Fix: Minor changes to formatting of SNMP IP table information

Description of changes contained in version 1.51 (10/9/2008)
	Fix: SNMP IP table now gives correct information

Description of changes contained in version v1.50 (7/18/2008)
	Add: New firmwares -- EM40/GM28, EM40/GM22-30, EM40/GM21, EM40/GM18, EM40/GM15-80W
	Add: Secondary alarm levels for all channels
	Add: DHCP Support
	Add: FTP Passive mode support for better compatibility with VPNs and firewalls during firmware updates
	Add: Friendly names enabled for all channels
	Add: Doctype declaration to each HTML page for better browser compatibility
	Add: Content Expiration header to all HTML documents to prevent browser caching of readings
	Change: Moved Friendly name assignment to new "Display" page
	Change: Moved Alarm settings to new "Alarms" page
	Change: device 'id' attribute in XML page now reads EM40<MAC> or EM08<MAC> based on firmware
	Change: XML alarm 'device-id' attribute matches device 'id' attribute
	Fix: Minor bug in some firmwares where SNMP traps were being sent with the wrong SNMP OIDs

Description of changes contained in version V1.40 (4/7/2008)
	Add: <alarm> fields in XML page for better Console compatibility.

Description of changes contained in version V1.36 (2/15/2008)
	Add: Software reboot functionality via front panel button.  
		 Hold button until c-IP shows.  Release button any time before d-IP shows.
		 While current IP is being displayed, press and release button twice to reboot.
		
Description of changes contained in version V1.35 (11/21/2007)
	Fix: Software change for CISPR 24 compliance.

Description of changes contained in version V1.34 (10/22/2007)
	Add: Second trap IP address.
	Add: Restore Defaults button added to configuration page.
	Change: LED Display shows "8.8.8.8." during bootup instead of staying blank.

Description of changes contained in version V1.20 (2/16/2007)
	Add: SNMP trap alarms.